web analytics
Shadow

Zhono Progeasy HP Chip Reset: 1215 & 1005 Technical Guide

Pre-Reset Inspection and Chip Identification

Many legacy HP monochrome and color chips share an almost identical 4-pad contact arrangement. Attempting to write an HP 1005 profile onto an HP 1215 color chip, or choosing the wrong regional variant, will result in a write error or an immediate “Supply Memory Error” (10.00.XX) inside the printer.

Before powering on the resetter, inspect and prepare the cartridge chip:

  1. Observe ESD Precautions: Cartridge chips contain CMOS memory components that are vulnerable to electrostatic discharge. Ground yourself on a metal chassis or work on an ESD mat, and hold the chip only by its PCB edges if it has been removed from the cartridge slot.

  2. Clean the Contact Pads: Residual toner dust, skin oils, or oxidation on the four gold contact pads can interrupt data transfer mid-write. Wipe the pads gently with a dry, lint-free swab or a small amount of isopropyl alcohol and allow them to dry completely.

  3. Check the PCB Alignment Notch: Inspect the small cutout (alignment notch) along the edge of the printed circuit board and note the layout of the contact pads relative to the plastic housing. The Progeasy interface uses notch orientation and board geometry to distinguish between visually similar HP profiles.

  4. Understand Credit Deduction Behavior: On the bench-tested legacy Progeasy configuration, reset credits stored on the USB dongle are deducted only when the screen confirms a completed write (“Success”). Failed reads, probe slips during identification, or unsupported chip messages did not deduct a credit during testing, though exact credit handling can vary by hardware revision and account type.

Executing the Zhono Progeasy HP Chip Reset

You can reset the chip while it remains seated in the toner cartridge housing or after sliding it out onto a flat, non-conductive work surface. Keeping the chip in a dedicated holder or flat on the bench often makes it easier to keep the four spring-loaded probe pins steady.

Step 1: Initialize the Progeasy Unit and Dongle

  1. Insert the authorized USB dongle containing your active reset credits firmly into the USB port on the Progeasy housing.

  2. Press and hold the power button for roughly 5 seconds until the LCD screen illuminates and loads the operating system.

  3. Confirm that the main menu recognizes the USB dongle and displays your remaining credit balance before touching a chip.

Step 2: Run Search Mode to Verify the Chip

Never skip directly to writing if you are unsure whether a chip is an original OEM board or a third-party compatible replacement.

  1. Select Search from the Progeasy main menu.

  2. Position the 4-pin contact adapter directly over the four conductive pads on the HP chip, matching the orientation indicated for the notch.

  3. Press down with steady, moderate vertical pressure so all four spring probes compress evenly against the pads without sliding.

  4. Read the detected parameters on the LCD screen—including model family, color channel (K, C, M, or Y for HP 1215 series), region code, and current supply status—to confirm that the hardware can communicate with the chip.

Step 3: Select the Profile and Write the Reset Data

  1. Exit Search mode and navigate to the manual model selection menu.

  2. Choose the exact profile matching your cartridge and physical PCB inspection (for example, HP 1215 and the corresponding color channel for a CB540A–CB543A cartridge, or HP 1005 for a CB435A cartridge).

  3. Align the four probe pins squarely onto the chip pads again and hold your hand completely still.

  4. Trigger the reset command on the device and maintain constant contact pressure until the progress cycle finishes.

  5. Wait for the LCD to display Success. Once confirmed, lift the probe adapter straight up off the contact pads. On dongle-based units, one credit is deducted at this stage.

Author

  • Tonercom.net

    Adil Toub is a Morocco-based printer repair technician specializing in laser printer diagnostics, maintenance, toner systems, and cartridge recycling. He holds a certificate in maintenance mechanics and draws on hands-on technical experience to create and review Tonercom’s repair guides. His work focuses on helping printer owners and technicians identify faults, understand maintenance procedures, and apply practical solutions safely and accurately. Through Tonercom.net, Adil publishes transparent, experience-based technical resources supported by careful research and manufacturer documentation.

Leave a Reply

Your email address will not be published. Required fields are marked *